 |
A
Leading Producer of PC Card Guides, Cages,
Ejectors, Mounts, Fan Pak's & IC Koolers |
 |
|
SUBRACK 90 VME
For VME and Multibus II Eurocard Systems
As one of the nation's pioneer
manufacturers of p.c. card cages, known for their versatility and low
cost, Unitrack offers the Subrack 90 VME. It is a basic subrack
compatible with Eurocard based bus systems and is ideal for those
developing VME systems. The basic Subrack 90 VME shown on these two
pages is for single or double-high boards. 3U to 9U heights and up
to 84 HP width. There are countless variations possible for VME bus
systems such as divided subracks for mixing 3U and 6U Eurocards in the
same 6U subrack; hinged or fixed front panels; top, bottom and back
panels; insulator strip card guides, etc. The Subrack 90 VME has an
attractive brushed aluminum finish, clear irridited. The sturdy
extrusions, end plates and other parts are accurately punched, drilled and
tapped. (Also available unassembled.) The Subrack 90 VME is
designed for Unitrack's card guides. These guides are available in
either non-conductive or conductive ESD (electrostatic discharge) plastic.
OPTIONS:
available for Subrack 90 VME
Support Bars
Tapped Bars
Vented Cover Panels (top, bottom, back)
Connector Adaptor Panels
Front Panels (3U or 6U high)
Hinged Door Panels
Cable Channel
Dividers
Insulator Strip (Noryl) |
Subrack 90 VME consists of the
following parts:
2 End Plates, 2 Mounting Flanges, 4 Support
Bars
2 Tapped Strips, Necessary Hardware |
| |
|
| |
An 84 HP wide Subrack 90 VME is
available with a divider so that single high and double high board
VME systems can be housed in one subrack. The divider can be
placed center, to the right or left. |
|
Another common variation is a
Subrack 90 VME to house both single high and double high boards
and also provide a built in cable channel. |
|
42 HP subracks are often used for
single high or double high boards. |
|
For those designing VME
packaging systems, we offer the various parts of the Subrack
90 VME as parts which can be purchased individually. In this
way you can build your own subrack to house boards of
different sizes. Our engineering department will work with you
to assist in packaging your system using our well engineered,
quality parts. Just call or FAX your requirements to us.
ORDERING INFORMATION
|
CAT NO. |
DESCRIPTION |
90VME3EPA
90VME3EPB
90VME6EPA
90VME6EPB
90VME9EPA
90VME9EPB
|
END
PLATES
For subrack to hold 160mm (A) card 3U high
For subrack to hold 220mm (B) card 3U high
For subrack to hold 160mm (A) card 6U high
For subrack to hold 220mm (B) card 6U high
For subrack to hold 160mm (A) card 9U high
For subrack to hold 220mm (B) card 9U high
|
90VME3MF1
90VME6MF1
90VME9MF1
|
MOUNTING
FLANGE
For 3U high subrack
For 6U high subrack
For 9U high subrack
|
V90160
V90220
|
CARD
GUIDES
For 160mm card
For 220mm card
|
90VME17SB
|
SUPPORT
BARS
For Subracks 17" long
|
90VME17TS
|
TAPPED
STRIP
Tapped strip 17" long (on .200 centers)
|
90VME17IS
90VME17TB
90VMA17VC
90VMB17VC
|
OPTIONS
Insulator spacer
Back support bars
Vented cover (A)
Vented cover (B)
|
Front panels are available
for 3U and 6U heights and various HP widths (4 and 8 HP
standard) to customer requirements of size, cutouts or silk
screening of legends, etc. Consult factory.
|
 |
 |
Card Guides are available in two sizes. Molded of
dimensionally stable polycarbonate with integral snap-in
buttons.
|
|
|
|
